# PrusaSlicer config bundle — eSun starter filament profiles
# Import via: File -> Import -> Import Config Bundle
# Generated 2026-08-05. Self-contained (no inherits), 0.4 mm nozzle assumptions.

[filament:eSun PETG @MK3S 0.4]
filament_vendor = eSun
filament_type = PETG
filament_diameter = 1.75
filament_density = 1.27
filament_colour = #00A040
extrusion_multiplier = 0.95
temperature = 238
first_layer_temperature = 240
bed_temperature = 90
first_layer_bed_temperature = 85
cooling = 1
fan_always_on = 1
min_fan_speed = 30
max_fan_speed = 50
bridge_fan_speed = 100
disable_fan_first_layers = 3
full_fan_speed_layer = 5
slowdown_below_layer_time = 15
fan_below_layer_time = 20
min_print_speed = 15
filament_max_volumetric_speed = 8
filament_retract_length = 1.2
filament_retract_speed = 35
filament_deretract_speed = 25
filament_retract_lift = 0.4
filament_retract_before_travel = 2
filament_wipe = 1
start_filament_gcode = "M900 K0.07 ; eSun PETG LA starting value - tune with PA tower"
filament_notes = "eSun PETG starter @MK3S. TDS: 230-250C (240 rec), bed 75-90C. Runs best at cool end. Glue stick on smooth PEI mandatory; check adhesion force even on textured. Dry 65C/6-8h. Tune EM and M900 K per spool colour."
compatible_printers_condition = printer_model=~/.*MK3.*/ and nozzle_diameter[0]==0.4

[filament:eSun PETG @MK4 0.4]
filament_vendor = eSun
filament_type = PETG
filament_diameter = 1.75
filament_density = 1.27
filament_colour = #00A040
extrusion_multiplier = 0.95
temperature = 235
first_layer_temperature = 240
bed_temperature = 85
first_layer_bed_temperature = 80
cooling = 1
fan_always_on = 1
min_fan_speed = 40
max_fan_speed = 60
bridge_fan_speed = 100
disable_fan_first_layers = 3
full_fan_speed_layer = 5
slowdown_below_layer_time = 10
fan_below_layer_time = 15
min_print_speed = 15
filament_max_volumetric_speed = 13
filament_retract_length = 0.8
filament_retract_speed = 35
filament_deretract_speed = 25
filament_retract_lift = 1.5
filament_retract_before_travel = 2
filament_wipe = 1
start_filament_gcode = "M572 S0.05 ; eSun PETG PA starting value - tune with PA tower at production accel"
filament_notes = "eSun PETG starter @MK4/MK4S. Prefers 235-240C. If overhangs droop, drop temp before adding fan. Dry 65C/6-8h. Tune EM and M572 S per spool colour."
compatible_printers_condition = printer_model=~/.*MK4.*/ and nozzle_diameter[0]==0.4

[filament:eSun PETG @COREONE 0.4]
filament_vendor = eSun
filament_type = PETG
filament_diameter = 1.75
filament_density = 1.27
filament_colour = #00A040
extrusion_multiplier = 0.95
temperature = 235
first_layer_temperature = 240
bed_temperature = 85
first_layer_bed_temperature = 80
cooling = 1
fan_always_on = 1
min_fan_speed = 30
max_fan_speed = 50
bridge_fan_speed = 100
disable_fan_first_layers = 3
full_fan_speed_layer = 5
slowdown_below_layer_time = 10
fan_below_layer_time = 15
min_print_speed = 15
filament_max_volumetric_speed = 14
filament_retract_length = 0.8
filament_retract_speed = 35
filament_deretract_speed = 25
filament_retract_lift = 1.5
filament_retract_before_travel = 2
filament_wipe = 1
start_filament_gcode = "M572 S0.05 ; eSun PETG PA starting value - tune with PA tower at production accel"
filament_notes = "eSun PETG starter @Core One. Chamber closed, <=40C. Enclosure reduces fan need vs open MK4. Dry 65C/6-8h. Tune EM and M572 S per spool colour."
compatible_printers_condition = printer_model=~/.*COREONE.*/ and nozzle_diameter[0]==0.4

[filament:eSun eTPU-95A @MK3S 0.4]
filament_vendor = eSun
filament_type = FLEX
filament_diameter = 1.75
filament_density = 1.21
filament_colour = #FF8000
extrusion_multiplier = 1.05
temperature = 230
first_layer_temperature = 235
bed_temperature = 50
first_layer_bed_temperature = 50
cooling = 1
fan_always_on = 1
min_fan_speed = 70
max_fan_speed = 100
bridge_fan_speed = 100
disable_fan_first_layers = 1
full_fan_speed_layer = 3
slowdown_below_layer_time = 20
fan_below_layer_time = 25
min_print_speed = 10
filament_max_volumetric_speed = 1.8
filament_retract_length = 0.8
filament_retract_speed = 20
filament_deretract_speed = 15
filament_retract_lift = 0
filament_retract_before_travel = 2
filament_wipe = 1
start_filament_gcode = "M900 K0 ; eTPU-95A: start with LA off, try 0.02-0.06 after flow is dialled"
filament_notes = "eSun eTPU-95A starter @MK3S. TDS: 210-250C, bed 45-60C, dry 55C/>4h (do 8-12h). LOOSEN IDLER vs PLA tension. Cooler+slower+more retraction beats hotter. Glue stick on smooth PEI. Dry filament is the #1 lever - target <30% RH."
compatible_printers_condition = printer_model=~/.*MK3.*/ and nozzle_diameter[0]==0.4

[filament:eSun eTPU-95A @MK4 0.4]
filament_vendor = eSun
filament_type = FLEX
filament_diameter = 1.75
filament_density = 1.21
filament_colour = #FF8000
extrusion_multiplier = 1.02
temperature = 228
first_layer_temperature = 230
bed_temperature = 50
first_layer_bed_temperature = 50
cooling = 1
fan_always_on = 1
min_fan_speed = 70
max_fan_speed = 100
bridge_fan_speed = 100
disable_fan_first_layers = 1
full_fan_speed_layer = 3
slowdown_below_layer_time = 15
fan_below_layer_time = 20
min_print_speed = 12
filament_max_volumetric_speed = 3.5
filament_retract_length = 0.6
filament_retract_speed = 25
filament_deretract_speed = 20
filament_retract_lift = 0.2
filament_retract_before_travel = 2
filament_wipe = 1
start_filament_gcode = "M572 S0.03 ; eTPU-95A PA starting value"
filament_notes = "eSun eTPU-95A starter @MK4/MK4S. Nextruder feeds TPU well - respect the MVS cap and it is drama-free. Dry 55C/8-12h, target <30% RH. Free-spinning spool mount, no side pull."
compatible_printers_condition = printer_model=~/.*MK4.*/ and nozzle_diameter[0]==0.4

[filament:eSun eTPU-95A @COREONE 0.4]
filament_vendor = eSun
filament_type = FLEX
filament_diameter = 1.75
filament_density = 1.21
filament_colour = #FF8000
extrusion_multiplier = 1.02
temperature = 228
first_layer_temperature = 230
bed_temperature = 50
first_layer_bed_temperature = 50
cooling = 1
fan_always_on = 1
min_fan_speed = 60
max_fan_speed = 90
bridge_fan_speed = 100
disable_fan_first_layers = 1
full_fan_speed_layer = 3
slowdown_below_layer_time = 15
fan_below_layer_time = 20
min_print_speed = 12
filament_max_volumetric_speed = 3.5
filament_retract_length = 0.6
filament_retract_speed = 25
filament_deretract_speed = 20
filament_retract_lift = 0.2
filament_retract_before_travel = 2
filament_wipe = 1
start_filament_gcode = "M572 S0.03 ; eTPU-95A PA starting value"
filament_notes = "eSun eTPU-95A starter @Core One. Door closed; slightly less fan than open-frame since chamber keeps layers warm. Dry 55C/8-12h, target <30% RH."
compatible_printers_condition = printer_model=~/.*COREONE.*/ and nozzle_diameter[0]==0.4

# ============================================================
# 0.6 mm nozzle filament variants
# ============================================================

[filament:eSun PETG @MK3S 0.6]
filament_vendor = eSun
filament_type = PETG
filament_diameter = 1.75
filament_density = 1.27
filament_colour = #00A040
extrusion_multiplier = 0.95
temperature = 242
first_layer_temperature = 245
bed_temperature = 90
first_layer_bed_temperature = 85
cooling = 1
fan_always_on = 1
min_fan_speed = 30
max_fan_speed = 50
bridge_fan_speed = 100
disable_fan_first_layers = 3
full_fan_speed_layer = 5
slowdown_below_layer_time = 15
fan_below_layer_time = 20
min_print_speed = 15
filament_max_volumetric_speed = 10
filament_retract_length = 1.2
filament_retract_speed = 35
filament_deretract_speed = 25
filament_retract_lift = 0.4
filament_retract_before_travel = 2
filament_wipe = 1
start_filament_gcode = "M900 K0.05 ; eSun PETG LA start for 0.6 - lower K than 0.4"
filament_notes = "eSun PETG @MK3S 0.6 nozzle. +5C vs 0.4 for the bigger melt load. Retune EM and K at this nozzle."
compatible_printers_condition = printer_model=~/.*MK3.*/ and nozzle_diameter[0]==0.6

[filament:eSun PETG @MK4 0.6]
filament_vendor = eSun
filament_type = PETG
filament_diameter = 1.75
filament_density = 1.27
filament_colour = #00A040
extrusion_multiplier = 0.95
temperature = 240
first_layer_temperature = 245
bed_temperature = 85
first_layer_bed_temperature = 80
cooling = 1
fan_always_on = 1
min_fan_speed = 40
max_fan_speed = 60
bridge_fan_speed = 100
disable_fan_first_layers = 3
full_fan_speed_layer = 5
slowdown_below_layer_time = 10
fan_below_layer_time = 15
min_print_speed = 15
filament_max_volumetric_speed = 15
filament_retract_length = 0.8
filament_retract_speed = 35
filament_deretract_speed = 25
filament_retract_lift = 1.5
filament_retract_before_travel = 2
filament_wipe = 1
start_filament_gcode = "M572 S0.035 ; eSun PETG PA start for 0.6 - lower S than 0.4"
filament_notes = "eSun PETG @MK4/MK4S 0.6 nozzle. Retune EM and PA at this nozzle; MVS 15 assumes stock MK4 hotend, raise toward 18-20 on MK4S."
compatible_printers_condition = printer_model=~/.*MK4.*/ and nozzle_diameter[0]==0.6

[filament:eSun PETG @COREONE 0.6]
filament_vendor = eSun
filament_type = PETG
filament_diameter = 1.75
filament_density = 1.27
filament_colour = #00A040
extrusion_multiplier = 0.95
temperature = 240
first_layer_temperature = 245
bed_temperature = 85
first_layer_bed_temperature = 80
cooling = 1
fan_always_on = 1
min_fan_speed = 30
max_fan_speed = 50
bridge_fan_speed = 100
disable_fan_first_layers = 3
full_fan_speed_layer = 5
slowdown_below_layer_time = 10
fan_below_layer_time = 15
min_print_speed = 15
filament_max_volumetric_speed = 16
filament_retract_length = 0.8
filament_retract_speed = 35
filament_deretract_speed = 25
filament_retract_lift = 1.5
filament_retract_before_travel = 2
filament_wipe = 1
start_filament_gcode = "M572 S0.035 ; eSun PETG PA start for 0.6"
filament_notes = "eSun PETG @Core One 0.6 nozzle. Chamber closed <=40C. Retune EM and PA at this nozzle."
compatible_printers_condition = printer_model=~/.*COREONE.*/ and nozzle_diameter[0]==0.6

[filament:eSun eTPU-95A @MK3S 0.6]
filament_vendor = eSun
filament_type = FLEX
filament_diameter = 1.75
filament_density = 1.21
filament_colour = #FF8000
extrusion_multiplier = 1.05
temperature = 230
first_layer_temperature = 232
bed_temperature = 50
first_layer_bed_temperature = 50
cooling = 1
fan_always_on = 1
min_fan_speed = 70
max_fan_speed = 100
bridge_fan_speed = 100
disable_fan_first_layers = 1
full_fan_speed_layer = 3
slowdown_below_layer_time = 20
fan_below_layer_time = 25
min_print_speed = 8
filament_max_volumetric_speed = 2.5
filament_retract_length = 0.8
filament_retract_speed = 20
filament_deretract_speed = 15
filament_retract_lift = 0
filament_retract_before_travel = 2
filament_wipe = 1
start_filament_gcode = "M900 K0 ; eTPU-95A 0.6: start LA off, larger orifice needs even less"
filament_notes = "eSun eTPU-95A @MK3S 0.6 nozzle. Bigger orifice = less back-pressure, so the drive copes slightly better than 0.4; MVS 2.5 still extruder-limited. Loosen idler, dry 8-12h."
compatible_printers_condition = printer_model=~/.*MK3.*/ and nozzle_diameter[0]==0.6

[filament:eSun eTPU-95A @MK4 0.6]
filament_vendor = eSun
filament_type = FLEX
filament_diameter = 1.75
filament_density = 1.21
filament_colour = #FF8000
extrusion_multiplier = 1.02
temperature = 230
first_layer_temperature = 232
bed_temperature = 50
first_layer_bed_temperature = 50
cooling = 1
fan_always_on = 1
min_fan_speed = 70
max_fan_speed = 100
bridge_fan_speed = 100
disable_fan_first_layers = 1
full_fan_speed_layer = 3
slowdown_below_layer_time = 15
fan_below_layer_time = 20
min_print_speed = 10
filament_max_volumetric_speed = 5
filament_retract_length = 0.6
filament_retract_speed = 25
filament_deretract_speed = 20
filament_retract_lift = 0.2
filament_retract_before_travel = 2
filament_wipe = 1
start_filament_gcode = "M572 S0.022 ; eTPU-95A PA start for 0.6"
filament_notes = "eSun eTPU-95A @MK4/MK4S 0.6 nozzle. MVS 5 is conservative; Nextruder may take 6+. Dry 8-12h."
compatible_printers_condition = printer_model=~/.*MK4.*/ and nozzle_diameter[0]==0.6

[filament:eSun eTPU-95A @COREONE 0.6]
filament_vendor = eSun
filament_type = FLEX
filament_diameter = 1.75
filament_density = 1.21
filament_colour = #FF8000
extrusion_multiplier = 1.02
temperature = 230
first_layer_temperature = 232
bed_temperature = 50
first_layer_bed_temperature = 50
cooling = 1
fan_always_on = 1
min_fan_speed = 60
max_fan_speed = 90
bridge_fan_speed = 100
disable_fan_first_layers = 1
full_fan_speed_layer = 3
slowdown_below_layer_time = 15
fan_below_layer_time = 20
min_print_speed = 10
filament_max_volumetric_speed = 5
filament_retract_length = 0.6
filament_retract_speed = 25
filament_deretract_speed = 20
filament_retract_lift = 0.2
filament_retract_before_travel = 2
filament_wipe = 1
start_filament_gcode = "M572 S0.022 ; eTPU-95A PA start for 0.6"
filament_notes = "eSun eTPU-95A @Core One 0.6 nozzle. Door closed. Dry 8-12h."
compatible_printers_condition = printer_model=~/.*COREONE.*/ and nozzle_diameter[0]==0.6

# ============================================================
# Print profiles - speeds pre-clamped to the matching filament MVS
# Flow math: speed cap = MVS / (layer_height x extrusion_width)
# ============================================================

[print:0.20 PETG @MK3S 0.4]
layer_height = 0.2
first_layer_height = 0.2
perimeters = 3
top_solid_layers = 5
bottom_solid_layers = 4
fill_density = 15%
fill_pattern = gyroid
seam_position = aligned
thin_walls = 0
ironing = 0
avoid_crossing_perimeters = 0
enable_dynamic_overhang_speeds = 1
extrusion_width = 0.45
first_layer_extrusion_width = 0.5
external_perimeter_speed = 25
perimeter_speed = 40
infill_speed = 55
solid_infill_speed = 40
top_solid_infill_speed = 30
bridge_speed = 25
gap_fill_speed = 25
first_layer_speed = 20
travel_speed = 180
default_acceleration = 1000
external_perimeter_acceleration = 800
perimeter_acceleration = 1000
infill_acceleration = 1250
first_layer_acceleration = 800
compatible_printers_condition = printer_model=~/.*MK3.*/ and nozzle_diameter[0]==0.4

[print:0.20 PETG @MK4 0.4]
layer_height = 0.2
first_layer_height = 0.2
perimeters = 3
top_solid_layers = 5
bottom_solid_layers = 4
fill_density = 15%
fill_pattern = gyroid
seam_position = aligned
thin_walls = 0
ironing = 0
avoid_crossing_perimeters = 0
enable_dynamic_overhang_speeds = 1
extrusion_width = 0.45
first_layer_extrusion_width = 0.5
external_perimeter_speed = 40
perimeter_speed = 100
infill_speed = 140
solid_infill_speed = 120
top_solid_infill_speed = 60
bridge_speed = 50
gap_fill_speed = 40
first_layer_speed = 25
travel_speed = 400
default_acceleration = 4000
external_perimeter_acceleration = 2000
perimeter_acceleration = 4000
infill_acceleration = 6000
first_layer_acceleration = 1000
compatible_printers_condition = printer_model=~/.*MK4.*/ and nozzle_diameter[0]==0.4

[print:0.20 PETG @COREONE 0.4]
layer_height = 0.2
first_layer_height = 0.2
perimeters = 3
top_solid_layers = 5
bottom_solid_layers = 4
fill_density = 15%
fill_pattern = gyroid
seam_position = aligned
thin_walls = 0
ironing = 0
avoid_crossing_perimeters = 0
enable_dynamic_overhang_speeds = 1
extrusion_width = 0.45
first_layer_extrusion_width = 0.5
external_perimeter_speed = 40
perimeter_speed = 110
infill_speed = 155
solid_infill_speed = 120
top_solid_infill_speed = 60
bridge_speed = 60
gap_fill_speed = 40
first_layer_speed = 25
travel_speed = 450
default_acceleration = 4500
external_perimeter_acceleration = 2500
perimeter_acceleration = 4500
infill_acceleration = 7000
first_layer_acceleration = 1000
compatible_printers_condition = printer_model=~/.*COREONE.*/ and nozzle_diameter[0]==0.4

[print:0.32 PETG @MK3S 0.6]
layer_height = 0.32
first_layer_height = 0.3
perimeters = 2
top_solid_layers = 4
bottom_solid_layers = 3
fill_density = 15%
fill_pattern = gyroid
seam_position = aligned
thin_walls = 0
ironing = 0
avoid_crossing_perimeters = 0
enable_dynamic_overhang_speeds = 1
extrusion_width = 0.68
first_layer_extrusion_width = 0.7
external_perimeter_speed = 20
perimeter_speed = 35
infill_speed = 42
solid_infill_speed = 35
top_solid_infill_speed = 25
bridge_speed = 20
gap_fill_speed = 20
first_layer_speed = 18
travel_speed = 180
default_acceleration = 1000
external_perimeter_acceleration = 800
perimeter_acceleration = 1000
infill_acceleration = 1250
first_layer_acceleration = 800
compatible_printers_condition = printer_model=~/.*MK3.*/ and nozzle_diameter[0]==0.6

[print:0.32 PETG @MK4 0.6]
layer_height = 0.32
first_layer_height = 0.3
perimeters = 2
top_solid_layers = 4
bottom_solid_layers = 3
fill_density = 15%
fill_pattern = gyroid
seam_position = aligned
thin_walls = 0
ironing = 0
avoid_crossing_perimeters = 0
enable_dynamic_overhang_speeds = 1
extrusion_width = 0.68
first_layer_extrusion_width = 0.7
external_perimeter_speed = 30
perimeter_speed = 55
infill_speed = 65
solid_infill_speed = 55
top_solid_infill_speed = 40
bridge_speed = 40
gap_fill_speed = 30
first_layer_speed = 22
travel_speed = 400
default_acceleration = 4000
external_perimeter_acceleration = 2000
perimeter_acceleration = 4000
infill_acceleration = 6000
first_layer_acceleration = 1000
compatible_printers_condition = printer_model=~/.*MK4.*/ and nozzle_diameter[0]==0.6

[print:0.32 PETG @COREONE 0.6]
layer_height = 0.32
first_layer_height = 0.3
perimeters = 2
top_solid_layers = 4
bottom_solid_layers = 3
fill_density = 15%
fill_pattern = gyroid
seam_position = aligned
thin_walls = 0
ironing = 0
avoid_crossing_perimeters = 0
enable_dynamic_overhang_speeds = 1
extrusion_width = 0.68
first_layer_extrusion_width = 0.7
external_perimeter_speed = 30
perimeter_speed = 60
infill_speed = 70
solid_infill_speed = 60
top_solid_infill_speed = 40
bridge_speed = 45
gap_fill_speed = 30
first_layer_speed = 22
travel_speed = 450
default_acceleration = 4500
external_perimeter_acceleration = 2500
perimeter_acceleration = 4500
infill_acceleration = 7000
first_layer_acceleration = 1000
compatible_printers_condition = printer_model=~/.*COREONE.*/ and nozzle_diameter[0]==0.6

[print:0.25 TPU @MK3S 0.4]
layer_height = 0.25
first_layer_height = 0.25
perimeters = 3
top_solid_layers = 4
bottom_solid_layers = 3
fill_density = 18%
fill_pattern = gyroid
seam_position = aligned
thin_walls = 0
ironing = 0
avoid_crossing_perimeters = 1
enable_dynamic_overhang_speeds = 1
extrusion_width = 0.48
first_layer_extrusion_width = 0.5
external_perimeter_speed = 12
perimeter_speed = 15
infill_speed = 15
solid_infill_speed = 15
top_solid_infill_speed = 10
bridge_speed = 12
gap_fill_speed = 12
first_layer_speed = 12
travel_speed = 120
default_acceleration = 1000
external_perimeter_acceleration = 800
perimeter_acceleration = 1000
infill_acceleration = 1000
first_layer_acceleration = 800
compatible_printers_condition = printer_model=~/.*MK3.*/ and nozzle_diameter[0]==0.4

[print:0.25 TPU @MK4 0.4]
layer_height = 0.25
first_layer_height = 0.25
perimeters = 3
top_solid_layers = 4
bottom_solid_layers = 3
fill_density = 18%
fill_pattern = gyroid
seam_position = aligned
thin_walls = 0
ironing = 0
avoid_crossing_perimeters = 1
enable_dynamic_overhang_speeds = 1
extrusion_width = 0.48
first_layer_extrusion_width = 0.5
external_perimeter_speed = 20
perimeter_speed = 28
infill_speed = 28
solid_infill_speed = 28
top_solid_infill_speed = 18
bridge_speed = 20
gap_fill_speed = 20
first_layer_speed = 15
travel_speed = 250
default_acceleration = 3000
external_perimeter_acceleration = 1500
perimeter_acceleration = 3000
infill_acceleration = 3000
first_layer_acceleration = 1000
compatible_printers_condition = printer_model=~/.*MK4.*/ and nozzle_diameter[0]==0.4

[print:0.25 TPU @COREONE 0.4]
layer_height = 0.25
first_layer_height = 0.25
perimeters = 3
top_solid_layers = 4
bottom_solid_layers = 3
fill_density = 18%
fill_pattern = gyroid
seam_position = aligned
thin_walls = 0
ironing = 0
avoid_crossing_perimeters = 1
enable_dynamic_overhang_speeds = 1
extrusion_width = 0.48
first_layer_extrusion_width = 0.5
external_perimeter_speed = 20
perimeter_speed = 28
infill_speed = 28
solid_infill_speed = 28
top_solid_infill_speed = 18
bridge_speed = 20
gap_fill_speed = 20
first_layer_speed = 15
travel_speed = 300
default_acceleration = 3000
external_perimeter_acceleration = 1500
perimeter_acceleration = 3000
infill_acceleration = 3000
first_layer_acceleration = 1000
compatible_printers_condition = printer_model=~/.*COREONE.*/ and nozzle_diameter[0]==0.4

[print:0.30 TPU @MK3S 0.6]
layer_height = 0.3
first_layer_height = 0.3
perimeters = 2
top_solid_layers = 4
bottom_solid_layers = 3
fill_density = 18%
fill_pattern = gyroid
seam_position = aligned
thin_walls = 0
ironing = 0
avoid_crossing_perimeters = 1
enable_dynamic_overhang_speeds = 1
extrusion_width = 0.68
first_layer_extrusion_width = 0.7
external_perimeter_speed = 8
perimeter_speed = 10
infill_speed = 11
solid_infill_speed = 10
top_solid_infill_speed = 8
bridge_speed = 10
gap_fill_speed = 8
first_layer_speed = 10
travel_speed = 120
default_acceleration = 1000
external_perimeter_acceleration = 800
perimeter_acceleration = 1000
infill_acceleration = 1000
first_layer_acceleration = 800
compatible_printers_condition = printer_model=~/.*MK3.*/ and nozzle_diameter[0]==0.6

[print:0.30 TPU @MK4 0.6]
layer_height = 0.3
first_layer_height = 0.3
perimeters = 2
top_solid_layers = 4
bottom_solid_layers = 3
fill_density = 18%
fill_pattern = gyroid
seam_position = aligned
thin_walls = 0
ironing = 0
avoid_crossing_perimeters = 1
enable_dynamic_overhang_speeds = 1
extrusion_width = 0.68
first_layer_extrusion_width = 0.7
external_perimeter_speed = 14
perimeter_speed = 20
infill_speed = 22
solid_infill_speed = 20
top_solid_infill_speed = 14
bridge_speed = 15
gap_fill_speed = 14
first_layer_speed = 12
travel_speed = 250
default_acceleration = 3000
external_perimeter_acceleration = 1500
perimeter_acceleration = 3000
infill_acceleration = 3000
first_layer_acceleration = 1000
compatible_printers_condition = printer_model=~/.*MK4.*/ and nozzle_diameter[0]==0.6

[print:0.30 TPU @COREONE 0.6]
layer_height = 0.3
first_layer_height = 0.3
perimeters = 2
top_solid_layers = 4
bottom_solid_layers = 3
fill_density = 18%
fill_pattern = gyroid
seam_position = aligned
thin_walls = 0
ironing = 0
avoid_crossing_perimeters = 1
enable_dynamic_overhang_speeds = 1
extrusion_width = 0.68
first_layer_extrusion_width = 0.7
external_perimeter_speed = 14
perimeter_speed = 20
infill_speed = 22
solid_infill_speed = 20
top_solid_infill_speed = 14
bridge_speed = 15
gap_fill_speed = 14
first_layer_speed = 12
travel_speed = 300
default_acceleration = 3000
external_perimeter_acceleration = 1500
perimeter_acceleration = 3000
infill_acceleration = 3000
first_layer_acceleration = 1000
compatible_printers_condition = printer_model=~/.*COREONE.*/ and nozzle_diameter[0]==0.6